|
|
Drive-in electrode M 20
For measurement of timber up to 50 mm thick. Electrode body of impact
resistant plastic. Included in the delivery are ten spare pins 16 mm and
23 mm
Ref. No. 3300
|
|
|
Modification Set M20-DS 16
For use of thinner pins(1.6mmØ) for testing timber up to 30mm thick,
consisting of 2 cap nuts (Ref.No. 3530) and 50 spare pins(Ref.No.4600)
Ref.No. 4310
|
|
|
Surface measurement caps M 20-OF 15
For moisture measurements on veneer up to a depth of about 3 mm and
surface measurement without damaging the material. Only in conjunction
with electrodes M 18 and M 20.
Ref. No. 4315 |
|
|
Ram-in electrode M 18
For measurement in depth of timber up to about 180 mm thick. Included in
the delivery are ten spare pins 40 mm and 60 mm long.
Ref. No. 3500
Teflon insulated electrode needles for point measurements at different
depths available on special order.
45 mm long Ref. No. 4550
60 mm long Ref. No. 4500 |
|
|
Stick-in electrode pins M 20-HW 200/300
Non-insulated pins for use with electrode M 20 for moisture checks
on chips, woodwool, veneer piles, etc.
Length 200 mm Ref. No. 4350
Length 300 mm Ref. No. 4355
|
|
|
Active electrode MH 34
With integrated measuring circuit for measurement of high moisture
contents in coniferous wood, specially in case of water-borne storage and
for pre-sorting of freshly cut timber for kiln drying.
Measuring range: 40 to 200 % m.c.
Ref. No. 3370
|
|
|
Drive-in electrode M 20
For measurements of soft, set building materials (plaster, gypsum, etc.).The
electrode body is of impact resistant plastic, including 10 spare pins 16
mm and 23 mm long.
Ref. No. 3300
|
|
|
Surface measuring caps M 20-OF 15
For moisture measurements on surfaces without damaging the material.
Effective up to depth of approx. 3 mm. (Only to be used with electrode M
20).
Ref. No. 4315
|
|
|
Stick-in electrode M 6
For measurement on hard, set building materials (mortar, concrete, etc.).
With two each electrode pins 23 mm, 40 mm and 60 mm long (only to be used
with contact paste).
Ref. No. 3700
|
|
|
Flat electrode pair M6-Bi 200/300
For measuring concrete or insulation materials in corner or expansion
joints (with insulated shank).
10 x 0,8
x 200 mm Ref.No. 3702
10
x 0,8
x 300 mm Ref.No. 3703
|
|
|
Pair of brush electrodes M 25
of stainless steel, for measurements on hard and soft building materials
without contact paste
Ref. No. 3740
|
|
|
Stick-in electrode pins M 20-Bi 200/300
For measurement of materials hidden beneath another panel or covering.
200 mm in length Ref. No. 4360
300 mm in length Ref. No. 4365
(only to be used with electrode M 20)
|
|
|
Deep electrodes M21-100/250
For deep measurements of all kinds of set building materials in
conjunction with contact paste.
100 mm in length Ref. No. 3200
250 mm in length Ref. No. 3250
|
|
|
Stick-in electrode pins M 6-150/250
Extra thin probes for measuring the moisture content in building and
insulating materials over expansion joints or through intersecting tile
joints, non-insulated. For use with electrodes M 6 and M 20.
150 x 3 mm Ref.No. 3706
250
x 2 mm Ref.No. 3707
|
 |
ET 10 Robust stick-in temperature
sensor for solid substances, bulk materials and fluids, length of probe
100 mm, Ø 3 mm,
measuring range –50 to 250 °C
Ref. No. 3165 |
 |
TT 40 Robust immersion and combustion
gas temperature sensor, length of probe 480 mm, dia. Ø 5 mm, measuring range
–50 to 350 °C
Ref. No. 3180 |
 |
LT 20 Fast reacting air/gas temperature
sensor with probe 480 mm long, dia. Ø 5 mm,
Measuring range –20 to 200 °C
Ref. No. 3190 |
|
|
TT 30 Robust immersion and combustion
gas temperature sensor, length of probe 230 mm, dia. Ø 3 mm, measuring range
–50 to 350 °C
Ref. No. 3185 |
 |
ET 50 Fast reacting stick-in
temperature sensor for soft solid substances, bulk materials and Fluids,
length of probe 120 mm, dia. Ø 3.0/2.3 mm,
measuring range –50 to 300 °C
Ref. No. 3160 |
 |
OTW 90 Angled special surface
temperature sensor for use at veneer presses etc., length of probe 100 mm,
dia. Ø 5 mm,
measuring range –50 to 250 °C
Ref. No. 3175 |
 |
OT 100 Spring
loaded, low mass surface temperature sensor, for use on wall surfaces, etc.
Length of probe 110 mm, dia. Ø 5 mm, measuring range –50 to 250 °C
Ref. No. 3170 |
|
|
OTW 480 Angled special surface
temperature sensor for use at veneer presses etc., length of probe 480 mm,
dia. Ø 5 mm,
measuring range –50 to 600 °C
Ref. No. 3176 |
 |
TT 480 Robust immersion and combustion
gas temperature sensor, length of probe 480 mm, dia. Ø 5 mm, measuring range
–50 to 600 °C
Ref. No. 3181 |
|
|
TT 600 Robust immersion and combustion
gas temperature sensor, length of probe 600 mm, dia. Ø 5 mm, measuring range
–50 to 600 °C
Ref. No. 3182 |
|
|
Special electrode RF-T 28
For high-speed testing of air relative humidity and air temp-erature,
complete with connection cable.
Measuring range: 7 to 98% R.H.,
–10 to +80°C.
Ref. No. 3155 |
|
|
Special electrode RF-T 36
For measurement of air humidity and air temperature, water activity value or
equilibrium moisture in rooms, warehouses or solid substances (e.g. concrete,
subflooring, masonry, etc.)
Measuring range: 5 to 98% R.H.,
–5 to +60°C.
Ref. No. 3136 |
|
|
Special electrode RF-T 36 T
For stationary installation for measurement of air humidity and air
temperature in rooms, ware-houses etc., technical details as with RF-T 36
but in transducer design with output 0 to 20 mA for temperature and humidity.
Ref. No. 3138 |
|
|
Plug-in Sensor RF-T 31
For measurement of atmospheric moisture, water activity value or equilibrium
moisture in bulk materials and solid substances, e.g. brickwork and other
building materials.
Measuring range: 7 to 98% R.H.,
-10 to +80°C.
Diameter 10 mm, sintered filter tip 32 mm long.
Insertion length 250 mm
Ref. No. 3131
Insertion length 500 mm
Ref. No. 3132 |
 |
Blade Sensor RF-T 32
For measurement of atmospheric humidity, water activity value and
equilibrium moisture in paper, leather, textile and tobacco stores etc.
Range of Measurement 7 to 98% R.H., –10 to +80°C.
Flat elliptical probe approx. 10 x 4 mm
Insertion length 250 mm
Ref. No. 3133
Insertion length 500 mm
Ref. No. 3134 |
|
|
Temperature probe FT
with connection cable and 7-pin plug 5 mm dia.
Measuring range: –20 to +120°C
FT 2 with connection cable 2 m long
Ref. No. 3195
FT 5 with connection cable 5 m long
Ref. No. 3196
FT 10 with connection cable 10 m long
Ref. No. 3197
FT 20 with connection cable 20 m long
Ref. No. 3198
FT 30 with connection cable 30 m long
Ref. No. 3199
|
|
|
Infra-red Surface Temperature
Sensor IR 40
Contactless temperature measurement from –20 to +199.9°C, resolution to
0.1°C, emission degree 95%, ratio of measured area to distance 2.5:1 (diameter
45 mm at a distance of 100 mm), sensor length 185 mm, diameter 32 mm, coiled
cable 400/1400 mm.
An ideal sensor for detection of heat bridges, determination of the dew
point temperature, measurement of live, moving or vibrating components as
well as measurement of components with low heat capacity, e.g. wood, glass,
insulating materials, etc., as well as for finding heating coils.
Ref. No. 3150 |
|
|
Matt-black stickers IR 30/E 95
Measurement spot 30 mm Ø, emissivity 95%, e.g. for measurement of metallic
surfaces.
Ref.No. 5833 |
|
|
Active electrode MB 35
with integrated measuring circuit, designed for surface measurement
on concrete, in particular before coating, painting or colour marking.
Measuring range: 2 to 8 % of dry weight
Ref. No. 3770
|
|
|
Active electrode B 50
with integrated measuring circuit, designed for non-destructive
location of moisture concentration in building materials and moisture
distribution in walls, ceilings and floors. The electrode uses a patented
process to create a high frequency field with a penetration depth up to
120 mm depending on the density of the tested building material.
Measuring range: 0 to 199 digits scanning range (classification
according to table).
0.3 to 8.5 % of dry weight, conversion of reading by table,
0.3 to 6.5 % CM, conversion of reading by table.
Ref. No. 3750
|
|
|
Active electrode B 60
with integrated measuring circuit, designed for non-destructive
location of moisture concentration in building materials and moisture
distribution in walls, ceilings and floors. The electrode uses a patented
process to create a high frequency field with a penetration depth up to
120 mm depending on the density of the tested building material. With
additional selector for setting a limit value between 20 and 140 digits
and acoustic signal generator.
Measuring range: 0 to 199 digits scanning range (classification
according to table).
0.3 to 8.5 % of dry weight, conversion of reading by table,
0.3 to 6.5 % CM, conversion of reading by table.
Ref. No. 3760
|
 |
Carrying Case I
For Hydromette H 35 and HT 65
with standard accessory.
Ref. No. 5051 |
 |
Carrying Case IV
For Hydromette H 35, HT 65, UNI 1, UNI 2 and HB 30 with standard and optional
accessory.
Ref. No. 5084 |
 |
Carrying Case V
For Hydromette HT 85 T, RTU 600, M 2050 and M 4050 with standard
and optional accessory.
Ref. No. 5085 |
 |
Contact Paste
For testing hard building materials
(flooring, concrete) in conjunction with
electrodes M 6 and M 21.
Ref. No. 5400
|
 |
Measuring cable MK 8
Suitable for all meters and electrodes.
Ref. No. 6210 |
 |
Measuring cable MK 15
For connection of TKMU to the meter for temperature measurement.
Ref. No. 6710 |
 |
BNC - adapter
for electrode main leads with two 4 mm, plugs to the transition to
BNC-connection with the Gann Hydromette
Ref.No. 6050 |
 |
Rechargeable battery
With charging unit suitable for all meters.
Ref. No. 5100 |
 |
Silicone heat conducting paste
To improve heat transmission on rough surfaces or where there are contact
problems. Unconditionally recommended with OT100.
Ref. No. 5500 |
 |
Filter Cap
For use with RF-T 28 in dust laden air or at high air speed
Ref. No. 3156 |
 |
Antistatic bracelet
flexibly, with 1,5m long grounding cable and
crocodile clamp, to the drainage of body statics,
Ref.No.
6075 |
 |
Bore hole adapter
For equilibrium moisture measurement in brick-work or building materials for
use with stick-in sensor RF-T 31
for bore holes up to 150 mm in depth
Ref. No. 5615
for bore holes up to 250 mm in depth
Ref. No. 5625
for bore holes up to 500 mm in depth
Ref. No. 5650 |
|
|
Thermo-printer TDH
portable compact printer for battery and mains operation for on-site
print-out measuring data stored with Hydromette
M 2050 and M 4050, complete with connecting cable MK 23, mains unit and one
roll of graph TDH 110, but without rechargeable battery
Ref. No. 9600 |
|
|
Accumulator Set 4.8
for thermo-printer
Ref. No. 9610 |
|
|
Roll of graph TDH 110
for thermo-printer TDH
Ref. No. 9640 |
|
|
Application program
DIALOG M Plus
PC software for transmission of memorized data to IBM compatible PC equipped
with operating system, WIN 9x/ ME, NT4.0, Win2000 and WinXP, complete with
PC connecting cable MK 19 and CD-Rom
Ref. No. 6081 |
|
UPDATE
for application program DIALOG (Ref. No. 6080), complete with 3.5” disk
and manual but without cable and against return of original disks.
Ref. No. 6086 |
|
|
Power supply unit 12
220 V/12 V = stabilized, recommended for lengthy data transmissions to a
PC or printer.
Ref. No. 5150 |
|
|
PC adapter 9/25 pin
for connection of cable MK 19 to a 25 pin PC input.
Ref. No. 6910 |
|
|
Connection cable MK 24
for connection of data logger KLIMA I – II to an IBM compatible PC
Ref. No. 6940 |
 |
Connection cable MK 17
9/25 pin, for connection of a printer with serial interface, e.g. EPSON LX
300/400
Ref. No. 6950 |
 |
Connection cable MK 19
9/9 pin, for connection of an IBM compatible PC.
Ref. No. 6900 |
 |
Connection cable MK 23
9/9 pin, for connection of Hydromette M2050 and M 4050 to thermoprinter
TDH
Ref. No. 6930 |
main
menue
